Appendix 1: Default Tag Values

Print Friendly, PDF & Email

Infra_Constant default tag values (controller-scoped tag)

TagDataDescription
HMI_Security_Level_Prog{...}HMI object security level settings
HMI_Security_Level_Prog[0]3Part Run selection list
HMI_Security_Level_Prog[1]0
HMI_Security_Level_Prog[2]3Rework button
HMI_Security_Level_Prog[3]3Fault clear button
HMI_Security_Level_Prog[4]0
HMI_Security_Level_Prog[5]3Tool selection
HMI_Security_Level_Prog[6]5Tool setup
HMI_Security_Level_Prog[7]5Module setup
HMI_Security_Level_Prog[8]5Part setup
HMI_Security_Level_Prog[9]0
HMI_Security_Level_Prog[10]3Manual buttons
HMI_Security_Level_Prog[11]5Module Recipe edit
HMI_Security_Level_Prog[12]3Module Recipe copy/paste
HMI_Security_Level_Prog[13]0
HMI_Security_Level_Prog[14]3Processing Assistant, Process Troubleshooting access
HMI_Security_Level_Prog[15]3Pass/Fail enable/disable setup
HMI_Security_Level_Prog[16]0
HMI_Security_Level_Prog[17]3Limits setup: Teach positions
HMI_Security_Level_Prog[18]5Limits setup: Position, Tolerance setting; Apply to All buttons
HMI_Security_Level_Prog[19]0
HMI_Security_Level_Prog[20]5
HMI_Security_Level_Prog[21]3Clear SPC History
HMI_Security_Level_Prog[22]0Clear Fault History
HMI_Security_Level_Prog[23]3
HMI_Security_Level_Prog[24]0Reset lamp on-time, lamp hours
HMI_Security_Level_Prog[25]0
HMI_Security_Level_Prog[26]0
HMI_Security_Level_Prog[27]0
HMI_Security_Level_Prog[28]0
HMI_Security_Level_Prog[29]0
HMI_Security_Level_Prog[30]0
HMI_Security_Level_Prog[31]0
ValveGroups_Used1Number of Valve Groups used
ValveGroup_Default{...}Default Valve Group settings
ValveGroup_Default.Name''Name of Valve Group
ValveGroup_Default.Punch_HoldTime5Time that Punch is extended when staking
ValveGroup_Default.Punch_DownTime0.25Time needed for Punch to extend (seconds)
ValveGroup_Default.BossPres_CheckTime1Max dwell time for Boss Height check (seconds)
ValveGroup_Default.BossPres_LowPrsEn0Use low pressure valve for Boss Height check
ValveGroup_Default.HighFlowCooling_En1Enable separate high flow cooling air valve
ValveGroup_Default.HighFlowCooling_Time20Time to maintain high flow cooling air (seconds)
ValveGroup_Default.CoolingAirTimeout30Time to keep low flow air on after end of cycle (seconds)
Module_Default{...}Default Module settings
Module_Default.Recipe{...}Heating parameters
Module_Default.Recipe.Energy0Area under the curve (per unit power-seconds)
Module_Default.Recipe.Energy_Low0Energy must be greater than this value
Module_Default.Recipe.RampTime0Initial heat time at full power (seconds)
Module_Default.Recipe.RampTime_High100Ramp Time must be less than this value
Module_Default.Recipe.SoakPower0.3186308Final soak power (0..1)
Module_Default.Recipe.SoakPower_High10Final Soak Power must be less than this value
Module_Default.Enable0Module enable/disable
Module_Default.Initialized01 = Module has valid Recipe
Module_Default.LampChk1Lamp fault checking enable/disable
Module_Default.StakeChk0Stake height checking enable/disable
Module_Default.BossChk0Boss height checking enable/disable
Module_Default.BossChk_w_FSSens0Use full stroke sensor as boss presence check (digital sensors only)
Module_Default.StakeHeight_Pos0.25Stake height positive positional tolerance, i.e. how far punch can underextend (mm)
Module_Default.StakeHeight_Nom0Stake height nominal position (mm)
Module_Default.StakeHeight_Neg0.5Stake height negative positional tolerance, i.e. how far punch can overextend (mm)
Module_Default.BossHeight_Pos0.5Boss height positive positional tolerance, i.e. how far punch can underextend (mm)
Module_Default.BossHeight_Nom10Boss height nominal position (mm)
Module_Default.BossHeight_Neg0.5Boss height negative positional tolerance, i.e. how far punch can overextend (mm)
Teach_Recipe_Default{...}Teach Mode: Default recipe array
Teach_Recipe_Default[0]{...}Teach Mode: Default recipe array
Teach_Recipe_Default[0].Energy2Area under the curve (per unit power-seconds)
Teach_Recipe_Default[0].Energy_Low0Energy must be greater than this value
Teach_Recipe_Default[0].RampTime1Initial heat time at full power (seconds)
Teach_Recipe_Default[0].RampTime_High100Ramp Time must be less than this value
Teach_Recipe_Default[0].SoakPower0.3186308Final soak power (0..1)
Teach_Recipe_Default[0].SoakPower_High10Final Soak Power must be less than this value
Teach_Recipe_Default[1]{...}Teach Mode: Default recipe array
Teach_Recipe_Default[1].Energy4Area under the curve (per unit power-seconds)
Teach_Recipe_Default[1].Energy_Low0Energy must be greater than this value
Teach_Recipe_Default[1].RampTime2Initial heat time at full power (seconds)
Teach_Recipe_Default[1].RampTime_High100Ramp Time must be less than this value
Teach_Recipe_Default[1].SoakPower0.3855433Final soak power (0..1)
Teach_Recipe_Default[1].SoakPower_High10Final Soak Power must be less than this value
Teach_Recipe_Default[2]{...}Teach Mode: Default recipe array
Teach_Recipe_Default[2].Energy6Area under the curve (per unit power-seconds)
Teach_Recipe_Default[2].Energy_Low0Energy must be greater than this value
Teach_Recipe_Default[2].RampTime3Initial heat time at full power (seconds)
Teach_Recipe_Default[2].RampTime_High100Ramp Time must be less than this value
Teach_Recipe_Default[2].SoakPower0.46650738Final soak power (0..1)
Teach_Recipe_Default[2].SoakPower_High10Final Soak Power must be less than this value
Teach_Recipe_Default[3]{...}Teach Mode: Default recipe array
Teach_Recipe_Default[3].Energy4Area under the curve (per unit power-seconds)
Teach_Recipe_Default[3].Energy_Low0Energy must be greater than this value
Teach_Recipe_Default[3].RampTime4Initial heat time at full power (seconds)
Teach_Recipe_Default[3].RampTime_High100Ramp Time must be less than this value
Teach_Recipe_Default[3].SoakPower1Final soak power (0..1)
Teach_Recipe_Default[3].SoakPower_High10Final Soak Power must be less than this value
Teach_Recipe_Default[4]{...}Teach Mode: Default recipe array
Teach_Recipe_Default[4].Energy7Area under the curve (per unit power-seconds)
Teach_Recipe_Default[4].Energy_Low0Energy must be greater than this value
Teach_Recipe_Default[4].RampTime7Initial heat time at full power (seconds)
Teach_Recipe_Default[4].RampTime_High100Ramp Time must be less than this value
Teach_Recipe_Default[4].SoakPower1Final soak power (0..1)
Teach_Recipe_Default[4].SoakPower_High10Final Soak Power must be less than this value
Teach_Recipe_Default[5]{...}Teach Mode: Default recipe array
Teach_Recipe_Default[5].Energy10Area under the curve (per unit power-seconds)
Teach_Recipe_Default[5].Energy_Low0Energy must be greater than this value
Teach_Recipe_Default[5].RampTime10Initial heat time at full power (seconds)
Teach_Recipe_Default[5].RampTime_High100Ramp Time must be less than this value
Teach_Recipe_Default[5].SoakPower1Final soak power (0..1)
Teach_Recipe_Default[5].SoakPower_High10Final Soak Power must be less than this value
Teach_Recipe_Default[6]{...}Teach Mode: Default recipe array
Teach_Recipe_Default[6].Energy3Area under the curve (per unit power-seconds)
Teach_Recipe_Default[6].Energy_Low0Energy must be greater than this value
Teach_Recipe_Default[6].RampTime2Initial heat time at full power (seconds)
Teach_Recipe_Default[6].RampTime_High100Ramp Time must be less than this value
Teach_Recipe_Default[6].SoakPower0.5644739Final soak power (0..1)
Teach_Recipe_Default[6].SoakPower_High10Final Soak Power must be less than this value
Teach_Recipe_Default[7]{...}Teach Mode: Default recipe array
Teach_Recipe_Default[7].Energy5Area under the curve (per unit power-seconds)
Teach_Recipe_Default[7].Energy_Low0Energy must be greater than this value
Teach_Recipe_Default[7].RampTime3Initial heat time at full power (seconds)
Teach_Recipe_Default[7].RampTime_High100Ramp Time must be less than this value
Teach_Recipe_Default[7].SoakPower0.68301344Final soak power (0..1)
Teach_Recipe_Default[7].SoakPower_High10Final Soak Power must be less than this value
Teach_Recipe_Default[8]{...}Teach Mode: Default recipe array
Teach_Recipe_Default[8].Energy7Area under the curve (per unit power-seconds)
Teach_Recipe_Default[8].Energy_Low0Energy must be greater than this value
Teach_Recipe_Default[8].RampTime5Initial heat time at full power (seconds)
Teach_Recipe_Default[8].RampTime_High100Ramp Time must be less than this value
Teach_Recipe_Default[8].SoakPower0.8264463Final soak power (0..1)
Teach_Recipe_Default[8].SoakPower_High10Final Soak Power must be less than this value
Teach_BossSize_Descriptions_in{...}Teach Mode: Description of each boss size
Teach_BossSize_Descriptions_in[0]'1/8 inch'
Teach_BossSize_Descriptions_in[1]'1/4 inch'
Teach_BossSize_Descriptions_in[2]'1/2 inch'
Teach_BossSize_Descriptions_mm{...}Teach Mode: Description of each boss size
Teach_BossSize_Descriptions_mm[0]'3 mm'
Teach_BossSize_Descriptions_mm[1]'6 mm'
Teach_BossSize_Descriptions_mm[2]'12 mm'
Teach_Color_Descriptions{...}Teach Mode: Description of each material color
Teach_Color_Descriptions[0]'Black'
Teach_Color_Descriptions[1]'Natural/Clear'
Teach_Color_Descriptions[2]'Other'
Teach_Recipe_Clipboard'PA Results'Teach Mode: Recipe clipboard name
Teach_PunchTime_Energy_Ratio1Teach Mode: Multiplier used to calculate punch dwell time
Lamp_MinRampTime0.5Minimum allowable Ramp rime (seconds)
PunchPosnTeachMax12.5Maximum punch position to enable pass/fail Teach buttons (mm)
Message_Dwell2Messages: Interval between subsequent messages (seconds)
Message_Fault_Lamp'Lamp Fault: Module 'Messages: Lamp Fault message text
Message_Fault_FullStroke'Full Stroke Fault: Module 'Messages: Full Stroke fault message text (digital sensor)
Message_Fault_FullStrokeCOS'Full Stroke Sensor Change of State Fault: Module 'Messages: Full Stroke change-of-state message text (digital sensor)
Message_Fault_BossPres'Boss Presence Fault: Module 'Messages: Boss Presence fault message text (digital sensor)
Message_Fault_BossPresCOS'Boss Presence Sensor Change of State Fault: Module 'Messages: Boss Presence change-of-state message text (digital sensor)
Message_Fault_StakeH'Stake Height Fault: Module 'Messages: Stake Height fault message text (analog sensor)
Message_Fault_BossH'Boss Height Fault: Module 'Messages: Boss Height fault message text (analog sensor)
Message_Fault_AnalogCOS'Analog Sensor Change of State Fault: Module 'Messages: Analog Sensor change-of-state message text (analog sensor)
Str_ValveGroup'Valve 'Valve Group string; Note trailing space
Str_Module'Module 'Module string; Note trailing space
Str_MODULE_caps'MODULE 'MODULE string, all caps; Note trailing space
Str_MODULES_caps'MODULES 'MODULES string, all caps; Note trailing space
Str_REWORK_caps' REWORK'REWORK string, all caps; Note leading space
Str_Tool'Tool 'Tool string; Note trailing space
Str_Part'Part 'Part string; Note trailing space
Str_BossP'Boss Presence'Boss Presence string
Str_BossH'Boss Height'Boss Height string
Str_FullStroke'Full Stroke'Full Stroke string
Str_StakeH'Stake Height'Stake Height string
Str_BossHeight_mm'Boss Height (mm)'Boss Height (mm) string
Str_BossHeight_in'Boss Height (in)'Boss Height (in) string
Str_FullStrokePosn_mm'Stake Height (mm)'Full Stroke Position (mm) string
Str_FullStrokePosn_in'Stake Height (in)'Full Stroke Position (in) string
Str_PunchExtend'Punch Extend Time (sec)'Punch Extend Time (sec) string